Welcome to Pursuit Boats Owners Forum
We are a boating forum for owners of Pursuit Boats to enthusiastically discuss all aspects of Pursuit Boat ownership. Whether you are looking for your first Pursuit or currently own one, you are sure to feel at home on PursuitBoatOwners.com
You are currently viewing our boards as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
Posts toplist
Rating posts
| Post | Been thanked | Author | Rating |
|---|---|---|---|
| PostSun Jan 01, 2023 7:57 pm 2002 Pursuit 3000 Express with water in the cabin 5280 As BNC said above. I have placed a bilge plug in the tube between the engine room and cabin. I took out all the lower rubber at the base of the windshield frame, and removed all the screws one at a time and put them back bedded in silicone. Leak stopped. This is exactly what I did and fixed is... |
1 | Woodworker2001 | Rating: 16.67% |
PostMon Jan 16, 2023 6:52 pm 2002 Pursuit 3000 Express with water in the cabin
It was just a standard expanding bilge pug |
1 | Woodworker2001 | Rating: 16.67% |
| PostThu Feb 17, 2022 2:51 pm 3000 Express Rudder Repair I do not know what stainless. But I changed seals a couple years ago. They still leaked so the next season I lowered one rudder about 1/2” and the other one 1/4”. They one I lowered close to a 1/2” didn’t leak anymore. The other one slowed but still leaked. I have to pull them back out with trans pr... |
1 | Woodworker2001 | Rating: 16.67% |
| PostMon Jan 16, 2023 6:56 pm 2002 Pursuit 3000 Express with water in the cabin 5294 Thanks Woodworker2001 Woodworker2001 , The rubber trim is pretty shrunken up and I was going to try to get a new set if I could find it. If you do have the part number that would be great! I would love to order it now in the offseason! Thanks for the help! Rich https://pompanette.com/store/rep... |
1 | Woodworker2001 | Rating: 16.67% |
| PostSat May 27, 2023 3:29 pm 2000 Helm Lift Not Working I had this problem on a 3000 express. Has 2 lifters and one worked but the other only worked going down. Ended up sending a request for help to pursuit. They quickly sent a picture of the relay location on the right side of the hull near the lifter and a schematic. Crazy system. There were 4 relays ... |
1 | Flyboy | Rating: 16.67% |
| PostFri Jun 04, 2021 7:16 pm Engine hatch actuator replacements I just replaced mine today on my 2460 Denali. Try Associated Spring/ Raymond in Maumee, Ohio. They were able to cross the part number and were fairly inexpensive. |
1 | DR Hyatt | Rating: 16.67% |
| PostSun Oct 11, 2020 4:19 pm 3000 Express Cabin Leak Alright guys. I found a cabin leak around Labor Day weekend when we were staying on the boat and had som very heavy rain. On the stbd side of the boat the carpet by the hanging locker was wet. We later found the front of the v berth cushions, the sweatshirts in the bottom of the hanging locker all t... |
1 | Woodworker2001 | Rating: 16.67% |
| PostSun Feb 13, 2022 6:53 pm 2470WA rear bench bolster attachment If anyone is interested, and have the rear bench seat over the fish locker, this is how that rear bolster is removed. Using a wooden wedge, you can start on the port end and gently tap the wedge behind the bolster till it starts to pull out. You then get a better view of where the nylon push pins ar... |
1 | bestmate | Rating: 16.67% |
| PostFri Jul 10, 2015 6:38 pm Re: 2002 2870 Gas Tanks Leaking Wow!!! That is unsettling because your boat is not very old (2002 is not an older boat in my book). 1. How did you know it was leaking? 2. How exactly did you get the floor up so you could remove the tanks? 3. What did you do for a replacement and did you figure out what caused the hole/leak? Thank ... |
1 | Idi_Amin | Rating: 16.67% |
PostFri Dec 11, 2020 7:44 pm 2001 Pursuit 3000 Express Ignition Switch
Have you opened the grey T.A.B.S box under the stairs? Checked the solenoids and connections in there? |
1 | Dan1 | Rating: 16.67% |
| PostThu Jan 13, 2022 3:19 pm 3070 express battery slide tray 2002 one of the worst thing about boat is battery access. but if you remove all the batteries it is possible to replace third one. the boat has a battery slide tray switch which makes a noise but it only moves an inch. but the real problem now is that i think the reservoir for the trim tabs after many ye... |
1 | greatharbor | Rating: 16.67% |
| PostSun Mar 12, 2023 6:26 am what is this switch 2002 3070 express ? 12 volt courtesy light, lights are probably in the stairs, circuit breaker on 12v panel? |
1 | Dan1 | Rating: 16.67% |
| PostFri Jul 08, 2022 6:58 am Merc 350 Horizon Fuel Pumps I have not had one go bad. I did have some injectors go bad. I know that there is nothing fun about changing the port fuel pump as it is on the outside of the engine. Best to get yourself midget gymnast with 7’ arms. Did you prime the water separating filter with fuel when you replaced it. Mine does... |
1 | Woodworker2001 | Rating: 16.67% |
| PostSun May 24, 2020 5:47 pm 3000 Express Side Vent Core Repair Finished the project yesterday. went down and cleaned it up today. I am happy with the results. I filled the void where the wood was rotted with G/flex. I thickened the epoxy with 404. Worked like a charm. I know I mentioned using a polyester resin, but like most anything i do, things change as the ... |
1 | DiverDux | Rating: 16.67% |
| PostMon Aug 22, 2016 2:17 pm Water under cabin stairs - 3100 Offshore check the anchor locker as well. known to leak into the cabin |
1 | Estimator | Rating: 16.67% |
| PostTue Jun 25, 2013 9:48 am 2870 galley sink upgrade Good day All, For those who have the worthless little sink in your pursuit galley, there is a fix. I finally got feed-up with not being able to wash a plate in the little oval fiberglass sink and replaced it with a Scandvik model 10993 SS sink. I was able to cut out the old one and lay in the replac... |
1 | Tclaude | Rating: 16.67% |
| PostThu Dec 14, 2023 10:33 am Cutlass Bearings I replaced mine about 5 years ago, maybe more. I believe the OD is 2 inches but you should verify that. I am looking for my records on that but I have sold that boat. |
1 | MarkT | Rating: 16.67% |
| PostThu Dec 14, 2023 9:37 pm Cutlass Bearings I measure mine at 2" OD. 1-1/2" Shaft. The strut is 6-3/16 long, but the bearing is set back and likely 6" long. 3000 express |
1 | bnc | Rating: 16.67% |
| PostTue Jan 09, 2024 6:47 am Trim Tabs - Carling switches - Trims Tabs Hydraulic System There's many variants of these switches, I think this is the one your looking for, stay away from the cheap Chinese versions of these switches, they will fail. https://www.greatlakesskipper.com/carli ... on-8-spade |
1 | Dan1 | Rating: 16.67% |
| PostMon Jan 29, 2024 7:02 pm Rod grommets Here you go. https://www.boatoutfitters.com/rod-and- ... ty-grommet |
1 | InsideTac | Rating: 16.67% |
Sponsors